ALLIED  FOAM  TECH  CORP.
(SINCE 1994)
(
Please visit our fire barrier foam site
with more focus on our fire rated composites development -

www.firebarrierfoam.com

2024
Allied Developed the Best Fire Rated Foam Composites per ASTM-E119 Test
non-brittle, vermiculite-free & no rust

   “fire “fire “fire “fire   


MISSION STATEMENT

Performance of currently available fire rated building materials, tested under commonly used thicknesses and densities, are really limited or inadequate in an actual fire.

Allied powerful fire barrier foam technologies/composites* could really have a chance to significantly reduce financial losses, save lives and save the environment during an actual fire.

 * confirmed recently by a major thermal testing lab. at just 1" (2.5 cm) thickness on a steel H beam per ASTM-E-119 test

FIRE HAZARD & TOXIC FUME RELEASE OF FLAMMABLE EXTERIOR BLDG. COMPOSITES
(effective fire barrier composites could avoid or significantly reduce the fire advancement)
(17,000 Californians to be striped of Fire Insurance (8, 2024)
FIRE RATED FOAM CEMENT,FIRE BARRIER FOAM CEMENT,FIRE RESISTANT FOAM CEMENT

fire rated foam cement,fire barrier foam cement,fire resistant foam cement fire rated foam cement,fire barrier foam cement,fire resistant foam cement fire rated foam cement,fire barrier foam cement,fire resistant foam cement
California, 8, 2024 Colorado, 12, 2021 Tianjin, 8, 2023 Dubai, 11,2022 London, 6, 2017

Allied fire barrier panels, boards have the highest compressive and bending strengths
vs autoclaved & cast-in-place foam cement products
Cement Composite Cure Condition Density Compr. Strength Bending Strength
AFT Fire Barrier Foam I RT 35 pcf 900 - 1,000 psi 370 - 500 psi
AFT Fire Barrier Foam II RT 35 pcf 650 - 750 psi 300-350 psi
AFT Portland Cem I/II RT 35 pcf 400 - 450 psi 100-200 psi
Autoclaved Concrete Autoclaving 35 pcf 600 - 700 psi 100 psi(?)

“fire

      
       Allied fire barrier foam has the highest fire rating per ASTM-E-119 Test
         against fire rated X-gypsum boards
foam cement,fire rated cement,fire barrier cement
“fire

(b>
                          Allied fire barrier foam has twice or better fire ratings per ASTM-E-119 Test
             over all fire rated intumescent coatings
“fire

ASTM-E-119 Tested H-Beams with Fire Rated Coatings
“fire “fire
H Beam with Allied Fire Barrier Foam
- 4 Hours to 2,000oF
H Beam with Intumescent Coating
- 2 Hours to 1,850
o F

Allied Fire Rated Foam Slurries Can be Cast as Panels or Sprayed onto Steel Structures

`
        Fire Panel Precast (< 10 pcf)            Fire Panel II at 11.5 pcf (185 kg/m3) Spray of Fire Rated Foam         Vertical Spray of Fire Rated Foam
foam cemenmt,fire rated cement,fire barrier cement foam cement,fire rated cement,fire barrier cement, E-119 foam cemenmt,fire rated cement,fire barrier cement foam cem,ent,fire barrier cement,fire rated cement

Fire rated, easy to handle, allow for pre-cast or cast-in-place manufacture.

Fire rated, easy to handle, allow for pre-cast or cast-in-place manufacture.

Sprayable with good adhesion to steel, non-hazardous, no rust & solvent free.

Sprayable with good adhesion to steel, non-hazardous, no rust & solvent free.

 
Excellent Bond Strengh (>> 1,000 psf ) of Allied 35 pcf (565 kg/m3) Fire Barrier Foam to A-36 Steel
for > 420 feet (128 meters) Buildings Applications per SFRM (Spray-applied Fire Resistant Material)
foam cement, fire rated cement, fire barrier cement

Please click "APPLICATIONS" for detailed ASTM-E119 test results comparing Allied fire barrier composite vs X gypsum & intumescent coatings


OTHER HIGHLIGHTS

HIGHLIGHT - JANUARY, 2016 (World Trade Center Phase II Project, New York)

Versatile Compact Foam Cement Mixing Pumping Setup - High Mobility with Good Output

World Trade Center, New York - Phase I (December, 2014) & Phase II (January, 2016) Geotech Fill Projects

“fire

“fire “fire

9/11 Memorial Museum (upper view)

Allied Geotech Setup - Museum in the back Allied Foam Liquid Tanks and Foamer Setup

“fire

“fire

“fire

Two Mixer/Pumpers on Either Side of Allied Foamer Two Pumping Hoses Going Down Geotech Fill for WTC Subway Stabilization
1/3 Yard Mobile Foam Cement Mixer/Pumper  above or Other Conventional Grout Mixer/Pumper. Adding Allied Foam to 1/3 Yard Mixer on the left. Grout Pumped through Hose to Indoor Site. Allied Foam Cement Grout over Unprimed Concrete Base. Allied Foam Cement Grout - Screed to Level. Load-bearing Topping Applied over 30 pcf Allied Foam Cement Grout.
Landscape Architechture on the Roof - An application with allied low slump foam cement
Harvard University - NorthWest Science Building, 530,000 ft2 multidisciplinary research facility
 The World's 1st Low Slump Geotechnical Roof Fill used Allied's Cement Composite Design, Foam Products & Machinery.

The award winning facility places more than half the total square footage of the facility below grade, and incorporates three functioning green roofs. The south facade of the Northwest Science Building defines a new South Yard, equipped with low landscape furniture. The yard is a green roof over extensive basement levels, with skylights bringing daylight into the underground areas.

Landscape Design Landscape on top of the Foam Cement-soil structure Recreation Area under the Foam Cement Composite Night View around the Landscape
“fire “fire “fire “fire
(Pre-project mockup work by Allied Foam Tech is shown below)
“fire “fire “fire “fire
Mixing & Pumping of High Applying of High Slump Loss Finished Foamed Cement Crown Cross-section of
Slump Loss Foam Cement Foam Cement on 1 Vertical/4 Horizontal Slope On Highly Sloped Geofoam Landscape after ~ 1 year

Foam Cement - With densities from over 1,450 kg/m3 (90 pcf) to as low as 48 kg/m3 (3 pcf) for geotechnical engineering & landscape architecture, lightweight concrete roof deck, lightweight wall and floor panels partitions lightweight concrete blocks insulative cinder block inserts.

Pervious Foam Cement - Allied pervious & non-pervious foamed cement are capable for waste encapsulation,       immobilization, soil stabilization and leachate filtration. Allied long lasting foam, applied as a surface cover on landfill sites and effluent ponds and lagoons, will effectively suppress noxious odors, vapors, litter and vectors, avoiding serious environmental issues.

 Insulative Fire Bricks, Panels -with excellent strength and thermal shock resistance for fabrication of  durable firebricks used as high performance insulative     materials for kilns and incinerators.

Geopolymer Foam- Flexible and very light (< 1.5 pcf or 24 kg/m3). Various geopolymer foam composites can achieve insulative value R > 3.8 per inch       and fire resistance.

Fire Barrier Foam -Specially formulated foam from Allied can be used as long duration fire fighting barriers for  the containment of forest fires.  

Our Mission
At Allied we are committed to the continuing development of versatile and highly stable aqueous foam and systems with a wide range of properties and applications that meet the specific needs of our customers in the various industrial sectors.
Technology

Allied Foam Tech has developed a universal foam technology for a wide range of industrial  and environmental applications. The excellent stability and dynamic nature of Allied's “fire make them ideal for use in  reducing the weight of cement/concrete, ceramics, firebricks, adhesives, coatings, and binders. Foam stability derived from Allied's many foam systems usually outranks that of any other existing technologies available in today s marketplace.

The AFT series of foam agents, using compressed air and Allied foam generating equipment, generates very fine and stable foams. They are used for the manufacture of  lightweight (or foamed) concrete, lightweight ceramics, insulative firebricks, alternative landfill cover, foam coatings, foam adhesives, long-duration firefighting foams and other uses. Substrates such as cement, concrete, coating formulations or others that incorporate Allied's foam products usually exhibit reduced weight with improved workability, insulation value, sound proofness, and expanded applications.

Allied  has also developed various models of compact and versatile foam generating equipment for production or field application  that can be manually or remotely controlled.

Postal address:
Allied Foam Tech Corp.
146 Keystone Drive 
Montgomeryville, Pa 18936, USA
(For more detailed contact info please see CONTACT page)